200, Jalan Sultan, #02-36A, Textile Centre, Singapore 199018 (Tel) : +65 62933968 / Operating Hours : (Mon-Fri 12pm-7pm) / (Sat & Eve of PH 12pm-6pm) / Sundays Close

Home

Email

facebook

Twitter

Youtube

Visit our Shopfront







 



SPEED CONTROLLERS
Flycolor Raptor BLS PRO BLHeli_S 30A 2-4S DSHOT Brushless ESC
New batch 26 April 2017 - DShot!




Flycolor Raptor BLS Pro BLHeli_S 30A 2-4S DSHOT Brushless ESC

DSHOT!

Specifications:

Brand name: Flycolor
Item name: 30A ESC
Con.Current: 30A
Burst Current(10s): 40A
BEC: NO
Lipo: 2-4s
Weight: 6.2g
Size: 26.5x13x5mm

Main features:
Supports BLHeli-s firmware
Supports oneshot/Mutishot/Dshot
Supports high KV Motors

Features:
• EFM8BB21F16G MCU, pipelined 8-bit C8051 core with 50 MHz maximum operating frequency;
• Dedicated high frequency driver, makes the start more smooth.
• ESC maximum speed is limited to 500k eRPM.
• BLHeli-S firmware is the next generation code, following the base BLHeli code. It designed for superior performance in multirotors, and uses. hardware generated motor pwm for smooth throttle response and silent operation.
• Support Damped light,causing very fast motor retardation, and inherently also does active freewheeling.
• Supports features to prevent sync loss. There are tuneable parameters that can make the code run well even in the most demanding situations,although default settings will work excellently in normal operating environments.
• The code supports regular 1-2ms pulse width input, as well as Oneshot125 (125-250us), Oneshot42 (41.7-83.3us) and Multshot (5-25us). The input signal is automatically detected by the ESC upon power up.
• Supports Dshot150, Dshot300 and Dshot600. Dshot is digital signal, anti-interference ability is stronger, and do not need throttle calibration.
• The silicone twisted-pair of the throttle signal cable increase the service life,and effectively reduces the crosstalk caused by signal transmission, and makes flight more stable.

Package Included:
1 X Raptor BLS Pro BLHeli-S 30A Brushless ESC











 

SGD$20.00
RAPTOR 30A PRO
(Each)




SGD$78.00
RAPTOR 30A PRO
(Set of 4 pcs)
















iPeaka EFM30A D-Shot ESC 4-IN-1 BLHELI_S (MUILTSHOT)
Supports DSHOT (No hardware mod required)



iPeaka EFM30A D-Shot ESC 4-IN-1 BLHELI_S - (MUILTSHOT)
DSHOT Compatible!


DShot is a new communication protocol between flight controller (FC) and ESC, substitute to Oneshot and Multishot. DShot stands for Digital Shot.

Specifications:

• BB21 MCU, 48Mhz Runs BLHELI_S J_H_xx firmware
• Supports 3-6S lipo input
• 4PWM input
• Current and Voltage output
• NO BEC
• Supports oneshot / Multishot / Dshot PWM
• Only 36x36mm, mount holes 30.5x30.5mm
• Supports damped light
• NO External capacitors needed

Package included:
1 x iPeaka EFM30A BLHeli_S D-shot 4-in-1 ESC
1 x Vsense and current cable
1 x PWM cable

Attention:
Attention: Please do not connect external devices like video transmitter, camera etc. directly to the power soldering point. (Adding BEC module to power the external devices is recommended.)

SGD$65.00


 

 

 

 

 

 

 

 

 

 


COBRA CP 35A ESC 2-6S BLHeliS
Supports DSHOT (No hardware mod required)


COBRA CP35A (2-6S) BLHELI_S (Opto)
DSHOT Compatible!


Specifications:
Item name: CP35A BLheli_S ESC
Weight (With Lead Wires): 6.4 grams
Max Continuous Current: 35 Amps
Burst Current rating (10s): 40 Amps
ESC Microprocessor: EFM8BB21F16 50MHz
Operating Voltage Range: 6 to 16 Volts
Number of Li-Po cells: 2 to 6 cells
BEC Output: None (OPTO)
ESC Size (mm): 28x 13
Programming: Yes
Supports : OneShot125 / OneShot42 / MultiShot / DShot without hardware modifications

Package included:
1 x CP35A BLheli_S ESC
3 x Motor wires

DShot 150/300 compatible
Please note this new batch is compatible with DShot and it is up to user to flash them on user-end side. We recommend using them as default unless you are certain enough to flash Dshot on them for what you deem is suitable for you. Good reference can be found here : https://www.rcgroups.com/forums/showthread.php?t=2756129&page=138
SGD$23.50
COBRA CP35A
(Each)




SGD$92.00
COBRA CP35A
(Set of 4 pcs)


COBRA CP 30A ESC 2-4S BLHeliS
Supports DSHOT (No hardware mod required)


COBRA CP30A (2-4S) BLHELI_S (Opto)
DSHOT Compatible!


Specifications:
Item name: CP30A BLheli_S ESC
Weight (With Lead Wires): 6.4 grams
Max Continuous Current: 30 Amps
Burst Current rating (10s): 35 Amps
ESC Microprocessor: EFM8BB21F16 50MHz
Operating Voltage Range: 6 to 16 Volts
Number of Li-Po cells: 2 to 4 cells
BEC Output: None (OPTO)
ESC Size (mm): 28x 13
Programming: Yes
Supports : OneShot125 / OneShot42 / MultiShot / DShot without hardware modifications

Package included:
1 x CP30A BLheli_S ESC
3 x Motor wires

DShot 150/300 compatible
Please note this new batch is compatible with DShot and it is up to user to flash them on user-end side. We recommend using them as default unless you are certain enough to flash Dshot on them for what you deem is suitable for you. Good reference can be found here : https://www.rcgroups.com/forums/showthread.php?t=2756129&page=138
SGD$20.00
COBRA CP30A
(Each)




SGD$78.00
COBRA CP30A
(Set of 4 pcs)


MAYTECH MT1601BLS USB PROGRAMMER for BLHELI_S

MAYTECH MT1601BLS USB Programmer BLHELI_S
MTUSB1601BLS is a usb programmer to download and program your Blheli_S firmware parameters.

Specifications:
Weight: 7.5g with wires and heat shrink wrap
Dimensions: 32.5 x 16.5mm

Features:
This handy tool allows you to quickly and easily update the firmware of your BLHELI_S ESC by connecting directly to the ESCs signal wire and then to the USB port of your PC. There is no need to cut open the heat shrink or use any additional interface components. Simply plug it in and go!

For upgrading multicopter ESCs with Silabs chips to BLheli_S firmware. Just connect the programmer to the ESC's servo cable and the other end to your computer. We recommend using RapidFlash for BLheli Suite for BLheli_S firmware.

MAIN FUNCTIONS:
• Loading BLheli_S Firmware to your ordinary airplane ESC.
• Upgrading BLHeli_S firmware to latest version.
• Programming BLHeli_S firmware parameters, so it can perform exactly as you want.

 

SGD$18.50
Each










LD Power 10A Multi-Rotor ESC (Opto)
LD Power 10A ESC (Opto - No BEC)
Specifications:
Input Voltage ................... 2S-3S Li-Po cells
Output Current ................ 10Amps Continous, 12 Amps Burst (10 Sec.)
Multi-Rotor Firmware : HW
Refresh : 490mhz
BEC Output ...................... Opto (No BEC)
High refresh rate for 180-250 Quad
Recommended motor : 1806 (2300KV)

This ESC are the ones featured in the LD Power 250 Quad Power combo set combo here : http://www.skyhobbies.com.sg/pagelink_drone_motor_combo.html

Package included:
- 1 x LD Power 10A ESC (OPTO)
- 2.0mm Gold Connectors Pre-Soldered

 

SGD$18.00
SGD$11.00
Each




iPeaka 20A ESC w/BLHeli firmware (BEC)
iPeaka BLHeli Series 20A ESC
Specifications:
Input Voltage ................ .. 2S-4S Li-Po cells
Output Current ................ 20Amps Continous, 25 Amps Burst (10 Sec.)
BEC Output ...................... Linear
Dimensions ...................... 52 x 24.5 x 10 mm
Weight .............................. 19 g

Features:
-Based on BLHeli firmware, further optimized to the perfect drive performance.
-Low-voltage protection, over-heat protection and throttle signal loss protection.
-Separate power supply for MCU and BEC, enhancing the ESC's ability of eliminating magnetic interference.
-Parameters of the ESC can be set via program card or transmitter.
-Throttle range can be set to be compatible with different receivers.
-Equipped with built-in linear BEC or switch BEC.
-Max speed: 210,000 rpm for 2-pole, 70,000 rpm for 6-pole, 35,000 rpm for 12-pole.


Package included:

- 1 x iPeaka 20A BLHeli ESC

 

SGD$22.00





CASTLE CREATIONS ICE LITE 50A
Castle Creations Phoenix Ice Lite 50 25V ESC
This is a Phoenix ICE Lite 50 amp brushless ESC from Castle Creations. This ESC has a 25.2 volts max input (20 NiMH/NiCad, 6 LiPo), is fully programmable, has heli features, is Castle Link compatible, has 5A switching BEC and Supports data logging. Recommended for electric sailplanes or weight/space critical applications.

PRODUCT SPECIFICATIONS :
Dimensions (LxWxH): 1.6x1.0x0.5” (40.6x26.4x12.7mm)
Max amps: 50 amps** (5 amp BEC)
Weight w/Wires: 1.7oz
Max volts: 25 volts / 6s LiPo / 20 cells NiCad/NiMh

**Ratings determined with a 5mph airflow on the ESC.

FEATURES:
•25.2 volts max input
•Fully Programmable
•Ideal when weight or space is critical

User guide :
http://www.castlecreations.com/support/documents/Phoenix_User_Guide.pdf

SGD$105.00


HOBBYWING Platinum 40A Pro
HOBBYWING Platinum Pro - 40A ESC
"Platinum" series ESC has the best performance, it is the top-class product for RC airplane and helicopter.

PRODUCT SPECIFICATIONS :
Output: Continuous 40A, burst 60A up to 10 seconds.
Input Voltage: 2-6 cells lithium battery or 5-18 cells NiMH battery.
BEC: 3A, 5.25V or 6V switchable by software.
Refresh rate of the throttle signal: 50Hz to 432Hz.
Control Signal Transmission: Optical/electrical coupled system.
Max Speed: 210000rpm for 2 Poles BLM, 70000rpm for 6 poles BLM, 35000rpm for 12 poles BLM. (BLM = BrushLess Motor)
Size: 59mm (L) * 27mm (W) * 12mm (H).
Weight: 38g.

FEATURES:
High performance microprocessor, best compatibility with all kinds of motors, highest driving efficiency.
Three types of start mode: Normal / Soft / Very-Soft, compatible with aircraft and helicopter.
Smooth, linear, quick and precise throttle response.
Multiple protection features: Low-voltage cut-off protection / Over-heat protection / Throttle signal loss protection.
The throttle signal is transfered through optical/electrical coupled system to avoid electromagnetic interference.
Perfect governor mode for helicopter.
Wide-opened heat-sink has the best heat dissipation effect.
The firmware of the ESC can be updated through the built-in USB adapter in the Professional LCD Program Box.
User programmable.
Multiple program methods supported: transmitter stick, Digital LED Program Card, Professional LCD Program Box, PC software. Very easy to program the ESC at home or at the flying field.


SGD$65.00


DYNAM RX REGULATOR (Switching)
Input: Use only2-cell (7.4V lipo)
Input connector : JST Female included
Output: 5.0V/6.0V
Current capability: 3A
Dimension: 20X30X7mm
Weight: 9g
Applications : EP Plane, Heli, 1/8GP and 1/10GP

SGD$9.50


Counter