200, Jalan Sultan, #02-36A, Textile Centre, Singapore 199018 (Tel) : +65 62933968 / Operating Hours : (Mon-Fri 12pm-7pm) / (Sat & Eve of PH 12pm-6pm) / Sundays Close






Visit our Shopfront


Flycolor Raptor-S Tower 30A BLHeli_S ESC +
F3 Flight Controller + OSD (2S-4S)



Flycolor Raptor-S Tower 30A BLHeli_S ESC + F3 Flight Controller + OSD (2S-4S)

All you need for your racing quad

This is a stacked tower made by FlyColor, combine 4-in-1 Raptor-S 390 30A BLHeli_S ESC and a F3 flight controller (target : SP Racing F3) and OSD module (MWOSD software) together, save a lot of weight and space on your racing quad.

• 4 ESC on 1 board, stack up with F3 Flight Controller
• Built-in 5V/1A and 12V/500mA BEC
• Built-in OSD module on the FC, you'll see main battery voltage and battery current on screen
• BLHeli_S firmware on ESC - the next generation coding for superior performance on racing drones
• ESC support OneShot 125, OneShot42, MultiShot, signal auto-detection during boot-up
• ESC support DShot150, DShot300 and DShot600, because they are digital signal which is anti-interference and does not require throttle range calibration

Flycolor Raptor-S Tower 30A BLHeli_S ESC Specifications :
• Con. Current : 30A
• Burst Current : 40A
• BEC : No
• Li-Po Cells : 2~4S
• Firmware : BLHeli_S
• Damped Light mode (Active braking)
• Dimension : 41.5 x 36mm x 19.6mm
• Mounting hole : 30.5x30.5mm
• Suitable for : 170-450 class multi-rotors
• Whole tower weight : 20 g

F3 Flight Controller + OSD Specifications :

Target : SP Racing F3
Built-in OSD function (MWOSD software)
Support PPM / PWM / SBUS
Port : USB / Boot / PWM / PPM / SBUS / 12V Camera / 12V VTX / LED / Buzzer / ISP (for factory use only)

Package included:
1 x Flycolor S Tower All-In-One














BetaFlight F3 Flight Controller



BetaFlight F3 Flight Controller


Betaflight F3 Flight controller (BFF3) is designed by FPVModel with co-operation of Boris B. (Betaflight creator and developer). It was made to support all Betaflight features in one single board. The BFF3 came flashed with Betaflight 3.1 firmware.

- F3 Processor
- MPU6000 Gyro/ACC Sensor
- 3 x UART ports (one for radio receiver)
- Built in 3A 5V BEC
- Built in OSD, configurable via Betaflight GUI
- SD Card adapter for BlackBox
- Current sensor
- Power distribution board with six-layer PCB
- Weight: 8.6g

BetaflightF3 is the flight controller designed to use every possible feature of Betaflight. More than the last half year has been spent in development. Boris B has worked with us to go over features and design aspects to help give us insight into what betaflight users want/need.

This board features a 3A power draw giving users extra room for added attachments through uart ports. The six layer PCB is a more expensive design approach but was needed to give the ability to have a PDB that was capable of having wiring pads on both the top and bottom of the board. By using the six layer design we were able to increase the size of the pads and work around all the components all the while giving esc connections in the corners of the board rather than bunching all connections on either the top OR the bottom. Featuring a fully functioning OSD that can be configured in Betaflight this board will make configuring your OSD a breeze.

The team at betaflight have been hard at work developing DSHOT and this board is also compatible with the latest release. But they didn't stop there, this board also features a micro adapter to accept Micro SD cards for those of you that like to follow up your flights with reviewing black box logging.

Package included:
1 x BFF3 Flight Controller
















iFlight REVO Bee - F4 - with OSD Flight Control
Betaflight CC3D REVO Firmware

iFlight REVO Bee - F4 - with OSD Flight Control Betaflight CC3D REVO Firmware


F3's upgrade version, using F405 instead of F303, could run faster loop time (double 8K speed). Supports DHOTS 150/300/600/1200 ESC.
Using F4 MCU controls OSD over SPI bus in DMA mode, OSD Configuration has been included in Betaflight GUI..

-Only 36x36mm, mount holes 30.5x30.5mm
-STM32 F405 MCU, Runs Betaflight 3.0 firmware, Cleanflight compatible
-5V 3A BEC BEC built-in
-PWM port reserved, support PWM/SBUS/PPM/IBUS/DSM2 input
-OSD built-in
-Port for Buzzer,programable LED light, low battery alarm reserved
-SPI Sensor MPU6000
-128Mbit Flash
-MPU6000 at SPI bus.
-Support SD card

Package included:
1 x iFlight REVO Bee F4 with OSDF Flight Control



















Item Name: SP Racing F3 Flight Control for Multicopter Deluxe Version
Version: Deluxe 6DOF (without MS5611 Barometer and HMC5883 Compass)
- 36x36mm board, 30.5 mm mounting holes.
- STM32F3 CPU.
- High-capacity Flash (Acro 6DOF and Deluxe 10DOF)
- MPU6050 Accelerometers and Gyroscopes
- MS5611 Barometer (Deluxe 10DOF)
- HMC5883 Compass (Deluxe 10DOF)
- MicroUSB socket.
- 4 x 4 pin JST-SH Socket (I2C, SWD, 2xuart)
- 2 x 8 pin JST-SH Socket (PPM, PWM, SERIAL RX, GPIO, ADC, 3V, 5V, GND)
- 8 x 3 pin though-holes for pin headers for ESC / Servo connections.
- 2 x 4 pin though-holes for the 2x serial ports .
- 2 x 2 pin though-holes for battery voltage and buzzer.

- Better coding practices and introducing tests, easier to maintain and for future development.
-Many bugs fixed from Baseflight. Supports more flight controllers, including CC3D, CJMCU and Sparky.
- Supports OneShot ESC and more than 8 RC channels.
- Additional PID controllers that uses floating point arithmetic operations. (now has 3 built-in PID Controllers)
- Many more features such as RGB LED strip support, Autotune, In-flight PID tuning with your radio, blackbox flight data logging etc.

Package included:
Deluxe 6DOF Version
1 x SP Racing F3 Flight Control for Multicopter (ACRO)
2 x 8p Wire Rod
2 x 4p Extension Path
5 x Pins set







F4 Flight Controller (CC3D Revo)

F4 Flight Controller (Acro)

Tons of features in one board with a wounder full layout:F4
- Uses the CC3D Revolution firmware.
- updated instantaneously with new releases.
- Stable SPI MPU-6000 Gyro
- All through hole pin header Design -no Sh connectors
- Direct Lipo input :1.5A Built-in onboard regulator - NO BEC needed. connect direct to a Lipo to power the board and Rx.
- RaceFlight or Betaflight support on an STM32 F3 with a SPI based MPU6000 gyro - low noise gyro will not force one to soft-mount the fc
- Boot-DFU button . No boot soldering required
- Blackbox support - Max 16mb for data logging
- SBUS/PPM input (Pinheaders) . 6PWM output (Pinheaders)
- Spektrum satellite port for direct connection - setup radio via USB power, woot woot!
- STM32 F405 MCU
- LED strip Port
- Buzzer Port (v2 buzzer port. working great in BF)
- Flashed tested and Ready to Fly after setup
- Only 36x36mm, mount holes 30.5x30.5mm

*ONLINE REFERENCE : https://www.rcgroups.com/forums/showthread.php?2732572-REVO-F4-STM32F405-Flight-Controller

Package included:

F4 flight Controller Board x 1pc
Connecting Pins x 1 lot






NAZE 32 "Mini" Flight Controller Rev. 5 (Acro)

NAZE 32 "Mini" (Acro) Flight Controller

- Version: Rev5
- USB Port
- Same Dimension as Mini CC3D ATOM
- Weight (Approx) Plain Board: 2g
- Board + Case + Pin Header: 6g

1 x Mini Naze32 Acro Flight Controller
1 x Protection Case
1 x Vertical Pin Headers (you need to solder the pins by yourself)
1 x Horizontal Pin Headers (you need to solder the pins by yourself)
2 x Cable Sets

Download User's Manual for rev5:
Configuration software - Chrome Baseflight Configurator (preferred) https://chrome.google.com/webstore/detail/baseflight-configurator/mppkgnedeapfejgfimkdoninnofofigk

Can also use 2.3 or newer version of MultiWiiConf (Java-based) from http://code.google.com/p/multiwii/downloads/list.

Software is open-source! Code repository at https://github.com/multiwii/baseflight







Flight Controller Anti-Vibration Plate Set
Flight Controller Anti-Vibration Plate Set


Item Name:Flight Controller Anti-Vibration Plate
Material: Plastic
Color: Black
Size:Same as CC3D/ Naze 32
Suitable flight controllers : Naze 32, CC3D, Mini APM,CC3D Atom
With Rubber Balls 4Pcs
Form Factor : For 36mm x 36mm Flight Controllers

Package Included:
1 X Flight Controller Anti-vibration Plate Set
4 X Rubber Balls